Looking to cut PVC pipe but not sure how to do it straight? In this blog post, we’ll show you how to cut PVC pipe straight, so you can get the job done right.
Checkout this video:
Materials Needed
-PVC pipe
-Tape measure
-Pencil
-PVC cutter or hacksaw
-File
##Instructions:
1. Measure the PVC pipe to the desired length using a tape measure, and mark it with a pencil. PVC pipe is usually sold in 1/2″ increments up to 10 feet in length, so if you need a 6″ piece, for example, you would mark it at 3″. If you are cutting multiple pieces of PVC pipe to the same length, stack them on top of each other and mark them all at once.
2. Place the blade of the PVC cutter or hacksaw on the line you drew in step 1, and cut through the pipe. If you are using a hacksaw, wrap electrical tape around the end of the blade to keep it from slipping. TIP: Make sure your cuts are straight by sighting down the length of the blade as you cut.
3. Use a file to remove any burrs from the inside or outside edge of the cut PVC pipe. These can be sharp and can cause injury if not removed.
PVC pipe
PVC pipe is a type of plastic piping that is used in a variety of applications. It is often used in plumbing and electrical applications, but it can also be used for crafts and other projects. PVC pipe is made from a type of plastic called polyvinyl chloride. It is a durable material that is easy to work with and does not corrode.
When cutting PVC pipe, it is important to cut the pipe straight. Otherwise, the pipe may not fit together properly or may not function correctly. Here are some tips on how to cut PVC pipe straight:
1. Measure the length of the PVC pipe that you need to cut. Mark the measurement with a piece of tape or a marker.
2. Use a sharp pencil to draw a line along the length of the PVC pipe at the mark that you made in step one.
3. Place the PVC pipe on a cutting surface. A board or table will work fine. Be sure that the cutting surface is level so that your cuts will be straight.
4. Place a ruler or a straight edge on top of the PVC pipe so that it crosses the line that you drew in step two. This will help you to make straight cuts.
5) Use a sharp utility knife or saw to cut along the line that you drew in step two. Be sure to apply pressure evenly so that your cuts are straight.
PVC cutter
A PVC cutter is a tool specifically designed to cut through PVC pipe. Use a handsaw for larger diameter pipe. Place the blade of the saw against the pipe and saw through the pipe with a back-and-forth motion.
Measuring tape
You will need a measuring tape to make sure that you are cutting your PVC pipe straight. Place the measuring tape on the side of the PVC pipe that you want to cut. Place the measuring tape at the top of the PVC pipe and extend it down to the bottom. Make a mark on the PVC pipe at the point where you want to make your cut.
Next, you will need a hacksaw or PVC cutter. If you are using a hacksaw, place the blade on the marked line and start sawing. If you are using a PVC cutter, open the jaws of the cutter and place them on either side of the marked line. Squeeze the handles of the cutter together to make your cut.
Now, you will need to use a file or sandpaper to remove any burrs from your cut PVC pipe. Be sure to file or sand in both directions to avoid creating any new burrs.
Test fit your newly cut PVC pipe into whatever fitting or other piece of PVC pipe it will be joining. If it is a tight fit, re-cut your pipe slightly larger and test fit again until you have a snug, but not too tight, fit.
Steps
Cutting PVC pipe can be tricky, but with a little practice it gets easier. The most important thing is to get a clean, straight cut. Here are a few tips on how to do that.
Measure the PVC pipe to the desired length using a measuring tape.
Making clean, straight cuts in PVC pipe is a necessary skill when working with the material for home plumbing projects. Although PVC pipe is relatively soft and easy to cut, it can be tricky to get a completely straight, clean cut without the proper tools and technique. In this article, we’ll show you the best way to cut PVC pipe so that your cuts are clean, consistent, and leak-free.
PVC is a type of plastic made from polyvinyl chloride. It’s strong and durable, making it an excellent choice for plumbing projects. PVC is also inexpensive and easy to find at most hardware stores.
When cutting PVC pipe, always use a sharp knife or saw blade. A dull blade will cause the PVC to crack or split, making it more difficult to get a clean, straight cut. You’ll also want to use a measuring tape or ruler to measure the PVC pipe before cutting it. This will help you make accurate cuts that are exactly the right size.
Once you’ve measured and marked the PVC pipe where you want to make your cut, position the pipe in a vise or clamp so that it’s securely held in place. This will allow you to make a safe, controlled cut without the risk of the pipe slipping or moving out of place.
Next, use a sharp knife or saw blade to carefully make your cut through the PVC pipe. If using a saw, be sure to keep the blade perpendicular to the pipe so that you don’t end up with an angled or curved cut. Once you’ve made your cut, remove any burrs or rough edges from the PVC with a file or sandpaper so that there are no sharp edges remaining.
Now you’re ready to use your newly cut piece of PVC pipe for your project! With these tips in mind, cutting PVC pipe should be quick and easy – giving you perfect, clean cuts every time
Place the PVC cutter around the PVC pipe.
The next step is to mark the spot where you want to cut the pipe. Place the PVC cutter around the PVC pipe where you want to make your cut. For a straight cut, it is important to make sure that the blade is lined up perfectly with the mark that you made on the pipe. You can use a pencil or a pen to make your mark. Once you have the cutter in place, squeeze the handles together until the blade cuts through the pipe.
Apply pressure to the PVC cutter and rotate it around the pipe.
Run the cutter around the pipe. As you do, apply firm pressure so that the blade can score the pipe. You’ll need to make at least one full rotation around the pipe, but you can go around more if you want to be extra certain that you’ve cut through completely.
Continue applying pressure and rotating the PVC cutter until it has cut through the entire pipe.
To ensure a clean, straight cut, it’s important to use a PVC cutter rather than a saw. A PVC cutter is a handheld rotating blade that scores the pipe as it rotates around it. This scoring action makes it much easier to get a clean break when you bend the pipe. Trust us, it’s worth the few extra dollars to get a proper PVC cutter!